Fit Series • Measuring Guide
By Imam Karakus • Founder, Shoescoo
Short answer: to measure foot width, stand with your full weight on a sheet of paper, hold a pen straight up and mark both sides of your foot at the widest part (the ball of the foot), then step off and measure straight across between the two marks with a ruler. That number, in millimetres or inches, is your width. A tape wrapped around the foot gives a different number, your girth. At Shoescoo we ask for both, plus your length, before we make a pair.
Most men have never measured the width of their feet, only the length. Then dress shoes pinch, the usual fix is to buy a bigger size, and the heel starts slipping. This guide shows the paper method we ask every Shoescoo customer to use: five minutes, a pen, a ruler, and two numbers that tell you far more than your shoe size does.
ALREADY HAVE YOUR NUMBERS?
- Send them to us for a free Fit Check: we reply with your size and whether you need Custom fit.
- Wide feet (E to 3E)? See how custom fit dress shoes (E to 3E) are built on a last from your measurements.
- Ready to shop: wide dress shoes for men, men's wide loafers, wide dress boots.
What you need (and when to measure)
- A sheet of paper longer than your foot. If your foot runs off a letter-size sheet, tape two sheets together.
- A pen or a sharp pencil.
- A ruler or a flat measuring stick with millimetres. A rigid ruler is better than a soft tape for width.
- A soft measuring tape, only if you also want your girth.
- A wall and a hard floor. Carpet lets the paper sink and adds error.
- The socks you'll wear with the shoes: thin dress socks for dress shoes and loafers, thicker socks for boots.
Measure in the evening. Feet swell a little through the day, especially after walking or standing at work. A shoe that fits your evening foot will still be comfortable in the morning; the opposite isn't true.
Have someone help if you can. You can do this alone, but it's easier and more accurate if a second person holds the pen while you stand still with your weight on the foot.
How to measure foot width at home, step by step
- Put the paper on a hard floor with one short edge flat against a wall.
- Stand on it with your heel touching the wall and your full weight on that foot. Don't sit. Your foot spreads when it carries your weight, and that's the foot your shoes have to hold.
- Mark your length: make a small mark at the tip of your longest toe. For many men that's the big toe; for some it's the second toe.
- Find the widest part of your foot. It's almost always across the ball of the foot, the joints just behind your toes, with the big-toe joint on the inside and the little-toe joint on the outside.
- Mark both sides of the widest part. Hold the pen straight up, at 90 degrees to the floor, and touch it to the side of your foot. Make a mark on the inside of the ball, then on the outside. A pen held at an angle slides under your foot and makes you look narrower, or leans out and makes you look wider.
- Step off and measure straight across between the two marks with the ruler. That distance is your foot width. Write it down in millimetres if you can; it's more precise than fractions of an inch.
- Measure the length from the paper's edge (where the wall was) to the toe mark.
- Repeat with the other foot. Most people have one foot slightly bigger. Your shoes are chosen for the bigger foot.
That's it: two numbers per foot, length and width, in about five minutes.
Why we don't use the traced outline
Many guides tell you to trace around your whole foot and measure the widest part of the drawing. The problem is the pen: as it travels around your foot it tilts, and the line ends up a few millimetres outside your real foot on each side. Two marks with an upright pen at the exact widest point are more accurate than a full outline.
Width vs girth: two different numbers
This is the most common measuring mistake we see, so it gets its own section.
- Width is the straight-line distance across the bottom of your foot at the widest part. You measure it flat, between two marks on paper.
- Girth (also called ball girth) is the distance around your foot at the same place: a soft tape wrapped over the top of the foot and under the sole, across the big-toe and little-toe joints.
Girth is always a much bigger number than width, because it goes over the top of your foot too. If you wrap a tape around your foot and send that as your "width", you'll look like you need a far wider shoe than you do, and a pair built on that number will be loose.
Both numbers are useful. Width tells a shoemaker how wide the sole and the bottom of the last must be; girth tells them how much volume the shoe needs over the top. That's why the Shoescoo Fit Check asks for length, width and girth, and why our custom-fit lasts are built from exactly those three.
How to measure girth (optional)
- Sit with your foot flat on the floor and your weight on it.
- Wrap a soft tape around the ball of the foot, over the big-toe joint on the inside and the little-toe joint on the outside.
- Pull it snug, flat against the skin, not tight. Read the number where the tape overlaps.
- Write it down and label it girth, so nobody confuses it with width.
What does your width number mean? D, E, 2E, 3E explained
US men's shoe widths use letters. From narrow to wide, the common ones are B (narrow), D (standard or medium), E (wide), 2E or EE (wide to extra wide), 3E or EEE (extra wide) and 4E and up (extra-extra wide). Each letter adds a small step of room across the ball of the foot and over the top.
Here's what most width charts don't tell you clearly:
- Width letters depend on your length. A width letter isn't a fixed number of millimetres. The same foot width that counts as wide on a size 8 can be roughly standard two sizes up, because a longer shoe is also cut wider. You can't read your width letter from your width measurement alone; you need your length too.
- Brands cut differently. Each maker builds on its own lasts. A 2E from one brand can feel like an E or a 3E from another, and some brands label "wide" without saying which letter they mean.
- Shoe styles differ too. A loafer and a boot from the same brand, in the same size and width, can fit differently, because the last and the opening are different.
That's why we don't publish a single millimetre-to-letter chart here: a number that's right for one length and one brand would mislead you at another. Send us your length, width and girth instead, and the free Fit Check tells you which size and fit you need on our lasts. For sizes, EU-to-US conversion and the rest of our sizing, see the men's shoe size guide.
Signs your feet are wide (even if you've never measured)
- The sides of your shoes bulge out over the sole after a few weeks.
- Your little toe gets red, numb or blistered in dress shoes.
- Shoes feel fine in length but pinch across the ball of the foot.
- You've been buying a half or full size bigger to stop the pinching, and now your heel slips.
- Boots and loafers hurt more than lace-ups, because there are no laces to open.
- Sneakers are comfortable but every leather shoe feels tight on day one.
If two or more sound familiar, measure. Many men we talk to have worn the wrong width for years and assumed leather shoes are simply uncomfortable.
7 measuring mistakes that give you the wrong number
1. Measuring while sitting
Without your weight on it, your foot is narrower and shorter. Stand, with your full weight on the foot you're measuring.
2. Using a tape around the foot as "width"
That's girth, not width. Width is a straight line across the bottom, between two marks.
3. Holding the pen at an angle
Keep it vertical. An angled pen can move your mark a few millimetres in either direction, and on width a few millimetres is a whole letter.
4. Measuring in the morning
Your foot is at its smallest. Measure after you've been on your feet for a while.
5. Measuring barefoot for boots
Wear the socks you'll wear with the shoes. A thick winter sock adds real volume.
6. Measuring one foot
Measure both. Buy for the bigger one.
7. Measuring on carpet
The paper sinks and wrinkles. Use a hard floor.
Can a Brannock device or an app measure width?
A Brannock device (the metal sizer in shoe stores) gives you a length size and a width letter in one go, and it's accurate when used standing. Its letters are a general US scale, though, so a brand's own lasts can still fit differently. If you've been measured on one, write down both the size and the width letter and send them with your paper measurements.
Phone apps that scan your foot are improving, but results depend on the camera, the angle and the lighting. If you use one, check its width against the paper method. Paper, a pen and a ruler cost nothing and are hard to get wrong.
In Chicago? We also offer free foot measuring in Chicago.
What to do with your measurements
- Compare your numbers to the brand you're buying from, not to a generic chart. Use their size guide, or ask them.
- Don't size up for width. A bigger size adds length first. The sides stop pinching, but your heel slips and the shoe creases in the wrong place. You need a wider shoe in your real length.
- Choose styles that forgive width. Derbies (open lacing) are the easiest dress shoe for a wide foot; loafers and pull-on boots are the hardest, because they can't open. More on this in our guide to the best dress shoes for wide feet.
- Know what leather can and can't do. Full-grain leather softens and shapes a little across the width over a couple of weeks. It doesn't turn a standard shoe into a wide one, and it never gets longer.
The easiest dress shoe for a wide foot
Cavalier Derby — Black · $219
A plain, moc-toe style derby. Open lacing gives a wide forefoot room, and it's smart enough for a suit.
Full-grain leather · Blake-stitched leather sole · Standard (D) or Custom fit (E to 3E) · US 7–14 · Made to order in about 3 weeks · Free US shipping, duties covered
See the Cavalier Derby →Not sure about size or width? Send us your foot measurements with the free Fit Check — we'll tell you your size and whether you need Custom fit.
How Shoescoo uses your measurements
Every Shoescoo pair is made to order by my dad, his team and me in our family workshop in Gaziantep, Türkiye. Before we start any pair, standard or custom, we confirm your size with you. You choose one of two fits:
- Standard fit: your usual US size on our standard (D) last. Free size exchange. Returns of unworn pairs within 30 days for store credit plus a $25 bonus, or a refund minus shipping.
- Custom fit: for any foot from E to 3E. We make a new last from your length, ball width and ball girth (built on your longer and wider foot), and build your pair on it. +$80 on one pair; two pairs on the same last +$40 in total. Because the pair is made for your feet, there are no returns; if the fit is off, we remake it once, free.
Dress shoes and loafers are $219, boots are $299, in US sizes 7 to 14. Shipping to the US is free and we cover customs duties; most pairs arrive in about three weeks. Every pair has a 12-month warranty against manufacturing defects.
Common Questions
How do I measure my foot width at home?
Stand on paper with your full weight on the foot, hold a pen upright and mark both sides at the widest part (the ball of the foot), then measure straight across between the marks with a ruler. Do it in the evening, in the socks you'll wear, for both feet.
Is foot width measured around the foot or across?
Across. Width is the straight line across the bottom of the foot at the widest part. The measurement around the foot with a tape is girth, a different and larger number.
Where is the widest part of the foot?
Across the ball of the foot: from the joint behind the big toe on the inside to the joint behind the little toe on the outside.
What foot width is considered wide for men?
It depends on your length. Width letters scale with shoe size, so the same width can count as wide on a size 8 and roughly standard two sizes up. Compare your length and width together, or send both to Shoescoo for a free Fit Check.
Should I measure my feet sitting or standing?
Standing, with your full weight on the foot you're measuring. Your foot spreads under load, and that's the foot your shoes have to fit.
Should I go up a size if my shoes are too narrow?
No. Going up adds length, not much width, so your heel slips and the shoe creases in the wrong place. Get a wider fit in your real length instead.
Can I measure foot width with a tape measure?
Yes, if you lay it flat across the two marks on the paper like a ruler. Wrapped around the foot, a tape measures girth, not width.
What is the difference between E, 2E and 3E?
They're steps of extra width: E is wide, 2E (EE) is wider and 3E (EEE) is extra wide, each with a little more room across the ball and over the top than the one before. Brands cut them differently. Shoescoo's Custom fit covers every width from E to 3E on a last made from your measurements.
Questions? DM us FIT on Instagram @shoescooo and send your three numbers.